|
Post by Chris72 on Dec 8, 2009 21:15:55 GMT 1
I've got a tp 1300 engine, would a 1600 top end rebuild kit fit?
Kit contains: 1 of Barrel & Piston Set, 85.5mm, 1600cc 2 of Cylinder Head, Complete, 1600cc, Dual Port 8 of Pushrod Tube, 1300-1600cc 1 of Engine Gasket Kit, 1300-1600cc 1 of Flywheel / Crankshaft, Oil Seal, 1200-1600cc
|
|
|
Post by Toughjeans on Dec 8, 2009 23:50:46 GMT 1
yes mate i'm pretty sure you can
|
|
|
Post by Chris72 on Dec 9, 2009 21:03:03 GMT 1
yes mate i'm pretty sure you can Thats all good then. What you like at engine rebuilds steve?
|
|
|
Post by steve66! on Dec 10, 2009 8:44:49 GMT 1
Steve's good..... and yes you can. just take it slowwwwww................ I'd advise you rip open the bottom end while you're at it, check out big ends and mains, clean out oil galleries etc, its not a big job once the top is off. Gimme a shout if you're stuck and i'll try to help... take it easy. steve
|
|
|
Post by Chris72 on Dec 10, 2009 19:28:50 GMT 1
Thanks for that. will take it slow.
|
|
|
Post by Toughjeans on Dec 10, 2009 19:47:52 GMT 1
yes mate i'm pretty sure you can Thats all good then. What you like at engine rebuilds steve? as soon as i manage to do one (ie vicky's stripped one in the garage, gathering dust i'll let you know!!) but yes mate i'll help out where i can. i'm hoping to get back into it over the xmas break.
|
|
|
Post by steve66! on Dec 10, 2009 21:24:57 GMT 1
Thats all good then. What you like at engine rebuilds steve? as soon as i manage to do one (ie vicky's stripped one in the garage, gathering dust i'll let you know!!) but yes mate i'll help out where i can. i'm hoping to get back into it over the xmas break. Oh steve, If i can help let me know, i'll pop over while my wife is working..... Been a while since i've done any aircooled! FUN FUN FUN!
|
|
|
Post by Chris72 on Dec 10, 2009 21:57:15 GMT 1
Im hoping to get the bits for engine over next couple of months. And any help would be seriously welcome ;D. Ive Turned our brick shed in to a nice little workshop with power now. Got a custom made work bench and all. ;D
|
|
|
Post by Toughjeans on Dec 11, 2009 1:13:32 GMT 1
as soon as i manage to do one (ie vicky's stripped one in the garage, gathering dust i'll let you know!!) but yes mate i'll help out where i can. i'm hoping to get back into it over the xmas break. Oh steve, If i can help let me know, i'll pop over while my wife is working..... Been a while since i've done any aircooled! FUN FUN FUN! i'll be giving you a shout mate don't you worry
|
|
|
Post by Toughjeans on Dec 11, 2009 1:14:38 GMT 1
Im hoping to get the bits for engine over next couple of months. And any help would be seriously welcome ;D. Ive Turned our brick shed in to a nice little workshop with power now. Got a custom made work bench and all. ;D no worries let me know,men and shed huh!!
|
|
|
Post by steve66! on Dec 11, 2009 8:36:47 GMT 1
grrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr
power tools!!!!
|
|
|
Post by axenige on Dec 11, 2009 21:11:37 GMT 1
Now, now sunshine there's nothing wrong with a dam good shed thank you very much, filled with lots of power and air tool plus enough bottled gases to blow up half the street. ;D P.S. I've just added to the Doktors shed complex a new 8 x 4 x 2 Olive drab Super storage box which now sits camouflage from prying eyes just outside the front of the main structure (Code name Big Shed) and just to the left hand side of the tool shed (Code name Little shed)
|
|